Gunite and Shotcrete Mixer

  • side of a Zim-Mixer gunite mixer

700 G Gunite Mixer

Our gunite mixer, the 700G series, is designed and manufactured for the gunite/shotcrete producer or any producer of wanting to mix a pre-blended aggregate with cement. This mixer utilizes a patented single material feed chain in the aggregate bin. The hydraulic system comes with a two section pump. An optional air pressure washout system is available.

✔ Patented single chain material feed system (unique only to the Zim-Mixer® brand!) which is the most accurate in the industry, is self cleaning, the longest lasting, and has the ability to run any material individually.

✔ Aggregate bin with no center divider.

✔ Cement bin with power agitator which includes a patented chain feed system (unique only to the Zim-Mixer® brand!) which is the most accurate in the industry, is self cleaning, and is the longest lasting.

✔ 2-Section hydraulic pump provides an independent pump for each hydraulic circuit which gives the most consistent mixing and coolest running hydraulic system in the industry.

✔ Automatic cam operated vibrators.

✔ Material counter.

✔ 9' mix auger with replaceable Ni-Hard wear pads.

✔ Power auger lift and swing.

✔ Hydraulic Oil Cooler

✔ Unit painting which includes two coats of epoxy primer and two coats of industrial grade polyurethane paint.

✔ Unit mounting on truck chassis, trailer, skid, etc...

✔ Calibration yield box.

✔ Operator training at customer location.

This renowned equipment combined with our industry leading technical support is why concrete professionals choose a Zim-Mixer®.

Admixture Systems

Allows the use of liquid admixtures such as Air Entraining Agents, Water Reducers, Super Plasticizers, Accelerators, and Set Retarders. A holding tank is loaded with the liquid, and charged with air pressure from the Mixer Unit. Each tank has an inline Filter, and an electrically triggered valve. This is integrated with the Material Feed Valve to allow the flow of material to stop and start with the other mix ingredients. Flow Meters are sized to meet the delivery requirements of the product being used, with ranges from 1 ounce to 3.5 gallons per minute. Each Flow Meter is certified to meet the tolerance requirements of ASTM, +/- 3%. There are no pumps to flush or maintain, and the air pressure can be used to evacuate the lines for easy draining and cleaning of the system.

         Low Flow Admixture System- For use with admixtures requiring lower dosages, a 20 Gallon Galvanized Tank is used (with a Stainless Steel Tank Optional) and a Flow Meter sized to meet the desired delivery rate.

         High Flow Admixture System- For use with admixtures requiring higher dosages, a 42 Gallon Galvanized Tank is used (with a Stainless Steel Tank Optional) and a Flow Meter sized to meet the desired delivery rate.

    

Pump Chute

This Chute is designed to aid in the placing of material into a concrete pump, wheelbarrow, or buggy. The lightweight 18 inch long chute quickly attaches to the discharge end of the mix auger, and minimizes any spills as well as simplifying wash out.

Spot Light Package

Provides light for nighttime operation. Lights illuminate the operator's control panel area, the aggregate bin material discharge area, and the work area.

Ticket Printers

         VR Ticket Printer- Resettable mechanical counter with a non-resettable totalizer. The totalizer is useful for scheduling periodic maintenance. This ticket printer provides an immediate record of the concrete delivered.

         VR Meter- Resettable mechanical counter with a non-resettable totalizer. The totalizer is useful for scheduling periodic maintenance.

    

Digital Metering System

With our Digital Metering System, there is no longer a need to convert a count number, with many variations for mix designs, into cubic yards. Our units are able to show the operator, as well as the customer, an actual reading of cubic yards produced at any given moment. The LCD panel at the operator's station shows the cubic yards produced on a continual basis.

Our in cab Interface Panel stores all of the necessary information that the operator needs, along with the current yardage being produced. Gate settings for aggregates, flow meter readings for admixtures (as many as 6), and specified strength for up to 99 mix designs can be stored. If so desired, the panel can also store the quantities per yard of each component of all 99 mix designs and can be printed on each ticket.

The in cab printer can be loaded with the name, address and phone number of the producer, as well as the actual yardage produced. The mix design can also be printed for D.O.T. requirements. The printed receipt is available in 1 or 2 part format, so that the customer can be given a copy. The system also produces a cumulative record of production for inventory control or maintenance purposes. The information is stored on a removable memory card and may be downloaded directly to a computer via a USB cable.

Bin Liner

An acrylic-reinforced aliphatic aromatic polyurethane coating applied to the inside of the aggregate bins to prevent bin abrasion, bin corrosion, and permit smooth flow of aggregates.

Electric Recoil Tarp

In cab switch provides easy operation to cover & uncover the aggregate bin. Most states require bin to be covered when loaded.

Aggregate Bin Screens

Prevents possible damage of equipment by screening materials through a 2-1/2" x 2-1/2" (63.5mm x 63.5mm) opening. All units sold outside the United States will be equipped with bin screens.

Stainless Steel Bins

This option includes the cement bin, aggregate bin, and mixer main frame being manufactured of grade 304 stainless steel. It provides the owner confidence that corrosion will not deteriorate the mixer regardless of environmental conditions.

Mixer Specifications (English)
Capacity 10 Yard 12 Yard 14 Yard 17 Yard
Production Rate (Yds./Hr.) 15 15 15 15
Cement (Ft.³) 96 96 113 130
Water (Gallons) Optional Optional Optional Optional
Ag Bin Capacity (Ft.³) 281 334 389 468
Empty Unit Weight (Pounds) Contact ZI Contact ZI Contact ZI Contact ZI
Hydraulic Pump (Sections) 2 2 2 2
Patented Chain Delivery System Yes Yes Yes Yes
Auger Length (Feet) 9 9 9 9
Auger Diameter (Inches) 9 9 9 9
Meets Standards:
ASTM C685 Yes Yes Yes Yes
AASHTO M241 Yes Yes Yes Yes
Certified VMMB Plate N/A N/A N/A N/A
CE Certified Yes Yes Yes Yes

Mixer Specifications (Metric)
Capacity 7.9m³ 9.4m³ 11.0m³ 13.2m³
Production Rate (m³/Hr.) 11.25 11.25 11.25 11.25
Cement (m³) 2.7 2.7 3.2 3.6
Water (Liters) Optional Optional Optional Optional
Ag Bin Capacity (m³) 7.9 9.4 11.0 13.2
Empty Unit Weight (kg) Contact ZI Contact ZI Contact ZI Contact ZI
Hydraulic Pump (Sections) 2 2 2 2
Patented Chain Delivery System Yes Yes Yes Yes
Auger Length (mm) 2743 2743 2743 2743
Auger Diameter (mm) 228.6 228.6 228.6 228.6
Meets Standards:
ASTM C685 Yes Yes Yes Yes
AASHTO M241 Yes Yes Yes Yes
Certified VMMB Plate N/A N/A N/A N/A
CE Certified Yes Yes Yes Yes
Chassis Specifications (English)
Capacity 10 Yard
12 Yard 14 Yard 17 Yard
Front Axle (Lbs.) 20,000
20,000
20,000
20,000
Rear Axle (Lbs.) 46,000
46,000 46,000
46,000
Cab to Axle (Inches)
155 155 155 155
Frame Width (Inches)
33.75 33.75 33.75 33.75
Number of Axles * * * *


Chassis Specifications (Metric)
Capacity 7.9M³ 9.4M³ 11.0M³ 13.2M³
Front Axle (Kg.) 9,072
9,072
9,072 9,072
Rear Axle (Kg.) 20,870*
20,870* 20,870* 20,870*
Cab to Axle (mm)
3937 3937 3937 3937
Frame Width (mm)
858 858 858 858


*Varies with state laws

Zimmerman Industries can supply you with a customized weight distribution package per your chassis and mixer specifications. Actual yardage carried with be determined by your analysis of regional weight regulations as well as weight rating of the chassis.

Please call our main office at 888-577-6499 (US only) or 717.733.6166 and speak to one of our sales people or complete the form below. We will work with you from the beginning of the inquiry to the final delivery of your machine.

Fields marked with a * are required.

Please prove you aren't a robot.

700 M Shotcrete Mixer

The 700M Series is designed to mix pre-blended aggregate with cement and water. Being in the 700 series line of equipment, it still has one material feed chain. This unit comes with a four section hydraulic pump and a standard water delivery system. The 700M can easily accommodate the same options as the basic rear discharge machine.

✔ Patented single chain material feed system (unique only to the Zim-Mixer® brand!) which is the most accurate in the industry, is self cleaning, the longest lasting, and has the ability to run any material individually.

✔ Aggregate bin with no center divider.

✔ Cement bin with power agitator which includes a patented chain feed system (unique only to the Zim-Mixer® brand!) which is the most accurate in the industry, is self cleaning, and is the longest lasting.

✔ Polyethylene water tank.

✔ Hydraulic water pump with a water solenoid valve which is quick acting for consistent mixing.

✔ Digital water flow meter.

✔ 4-Section hydraulic pump provides an independent pump for each hydraulic circuit which gives the most consistent mixing and coolest running hydraulic system in the industry.

✔ Automatic cam operated vibrators.

✔ Material counter.

✔ 9' mix auger with replaceable Ni-Hard wear pads.

✔ Power auger lift and swing.

✔ Manual telescopic chutes, which are mounted to the auger and require no attachment by the operator.

✔ Unit painting which includes two coats of epoxy primer and two coats of industrial grade polyurethane paint.

✔ Unit mounting on truck chassis, trailer, skid, etc...

✔ Calibration yield box.

✔ Operator training at customer location.

This renowned equipment combined with our industry leading technical support is why concrete professionals choose a Zim-Mixer®.

Admixture Systems

Allows the use of liquid admixtures such as Air Entraining Agents, Water Reducers, Super Plasticizers, Accelerators, and Set Retarders. A holding tank is loaded with the liquid, and charged with air pressure from the Mixer Unit. Each tank has an inline Filter, and an electrically triggered valve. This is integrated with the Material Feed Valve to allow the flow of material to stop and start with the other mix ingredients. Flow Meters are sized to meet the delivery requirements of the product being used, with ranges from 1 ounce to 3.5 gallons per minute. Each Flow Meter is certified to meet the tolerance requirements of ASTM, +/- 3%. There are no pumps to flush or maintain, and the air pressure can be used to evacuate the lines for easy draining and cleaning of the system.

         Low Flow Admixture System- For use with admixtures requiring lower dosages, a 20 Gallon Galvanized Tank is used (with a Stainless Steel Tank Optional) and a Flow Meter sized to meet the desired delivery rate.

         High Flow Admixture System- For use with admixtures requiring higher dosages, a 42 Gallon Galvanized Tank is used (with a Stainless Steel Tank Optional) and a Flow Meter sized to meet the desired delivery rate.

    

Manual Chute System

This Chute System is standard equipment on all 400N1 series units. It is attached to the auger, and takes up no space on the decks of the unit. When in use, the discharge angle is adjustable, and the chutes can extend from 4 to 8 feet in six inch increments, allowing for a wide area of coverage. Since it is attached to the auger, it is moved by the Operator and requires no additional personnel.

Hydraulic Power Telescopic Chutes

This Chute System allows the Operator to change the angle of delivery as well as the length of the chute from 5 to 11 feet in any increment required. It is especially useful in flatwork applications, as a large area can be placed without moving the mixer, and without the need of additional personnel. As with the Manual Telescopic Chutes, it is attached to the Auger and takes up no space when not in use.

Swivel Chutes

This Chute System allows concrete to be placed in areas not reachable by fixed chutes. As with the other ZI Chute Systems, it is attached to the Auger and takes up no additional space on the unit when not in use, and requires no additional personnel. A ring is used at the top of the chute, and allows rotation in a 200 degree arc. This enables the concrete to be placed alongside the mixer, and is especially useful in curbing or trenching applications. The Chute angle is adjustable, and it is in a 2 piece configuration that can extend to either 5 feet or 10 feet from the end of the Auger.

Pump Chute

This Chute is designed to aid in the placing of material into a concrete pump, wheelbarrow, or buggy. The lightweight 18 inch long chute quickly attaches to the discharge end of the mix auger, and minimizes any spills as well as simplifying wash out.

Spot Light Package

Provides light for nighttime operation. Lights illuminate the operator's control panel area, the aggregate bin material discharge area, and the work area.

Ticket Printers

         VR Ticket Printer- Resettable mechanical counter with a non-resettable totalizer. The totalizer is useful for scheduling periodic maintenance. This ticket printer provides an immediate record of the concrete delivered.

         VR Meter- Resettable mechanical counter with a non-resettable totalizer. The totalizer is useful for scheduling periodic maintenance.

    

Digital Metering System

With our Digital Metering System, there is no longer a need to convert a count number, with many variations for mix designs, into cubic yards. Our units are able to show the operator, as well as the customer, an actual reading of cubic yards produced at any given moment. The LCD panel at the operator's station shows the cubic yards produced on a continual basis.

Our in cab Interface Panel stores all of the necessary information that the operator needs, along with the current yardage being produced. Gate settings for aggregates, flow meter readings for admixtures (as many as 6), and specified strength for up to 99 mix designs can be stored. If so desired, the panel can also store the quantities per yard of each component of all 99 mix designs and can be printed on each ticket.

The in cab printer can be loaded with the name, address and phone number of the producer, as well as the actual yardage produced. The mix design can also be printed for D.O.T. requirements. The printed receipt is available in 1 or 2 part format, so that the customer can be given a copy. The system also produces a cumulative record of production for inventory control or maintenance purposes. The information is stored on a removable memory card and may be downloaded directly to a computer via a USB cable.

Bin Liner

An acrylic-reinforced aliphatic aromatic polyurethane coating applied to the inside of the aggregate bins to prevent bin abrasion, bin corrosion, and permit smooth flow of aggregates.

Electric Recoil Tarp

In cab switch provides easy operation to cover & uncover the aggregate bin. Most states require bin to be covered when loaded.

Fiber Dispenser

The use of fiber reinforced concrete within the construction industry is growing at a rapid rate. In fact, because of it's structural benefits, many architects and engineers are specifying fiber reinforced concrete in their projects. Zimmerman Industries has a patented fiber feeder that will automatically introduce the fiber into the mix auger.

The feeder is powered by a variable speed hydraulic motor, so the amount of fiber can be adjusted to meet various specifications. The fibers are stretched and fluffed through the use of rotating fingers and a high volume air flow system insures a consistent material flow to the mix auger. The Fiber Dispenser uses 1/2" to 1 1/4" (12.7mm to 31.75mm) polypropylene monofilament.

Features and benefits include:

         * Automatically feeds fiber

         * Fluffs and stretches fibers

         * Buy fiber in bulk, not bags

         * Eliminate manual feeding

         * Increased accuracy

         * Patented system

Liquid Color System

Our Liquid Color System can be used with various manufacturers' liquid color products and is designed to allow changes of color in minutes. The variable speed peristaltic pump not only compensates to allow the changes of color needed (based on manufacturer's specifications), but also provides the availability to produce shades of each color.

Cleaning of the system can be done in minutes by simply flushing the system with clean water. The system is also designed so that it can be used to pump the liquid color from its' shipping container into the dispensing tanks.

Aggregate Bin Screens

Prevents possible damage of equipment by screening materials through a 2-1/2" x 2-1/2" (63.5mm x 63.5mm) opening. All units sold outside the United States will be equipped with bin screens.

Water Tank Deck Fill Port

Provides deck level fill port for the water tank. Prevents operator from having to climb on top of unit to fill water tank. Uses 1-1/2" (38.1mm) coupling.

Hydraulic Oil Cooler

This option can be added when high ambient temperatures are common. The radiator will help keep the hydraulic oil cool, extending the life of critical hydraulic components.

Stainless Steel Bins

This option includes the cement bin, aggregate bin, and mixer main frame being manufactured of grade 304 stainless steel. It provides the owner confidence that corrosion will not deteriorate the mixer regardless of environmental conditions.

Insulated Water Tank

Non-transparent insulated blanket fastens to poly water tank insuring water temperature stays constant.

Variable Speed Cement

This option provides the ability to hydraulically control the cement feed with an infinite number of possibilities. This is most commonly used for companies with mix designs which require atypical cement/pozzolan addition rates.

Mixer Specifications (English)
Capacity 10 Yard 12 Yard 14 Yard 17 Yard
Production Rate (Yds./Hr.) 30 30 30 30
Cement (Ft.³) 96 96 113 130
Water (Gallons) 500 500 500 500
Ag Bin Capacity (Ft.³) 281 334 389 468
Empty Unit Weight (Pounds) Contact ZI Contact ZI Contact ZI Contact ZI
Hydraulic Pump (Sections) 4 4 4 4
Patented Chain Delivery System Yes Yes Yes Yes
Auger Length (Feet) 9 9 9 9
Auger Diameter (Inches) 9 9 9 9
Meets Standards:
ASTM C685 Yes Yes Yes Yes
AASHTO M241 Yes Yes Yes Yes
Certified VMMB Plate N/A N/A N/A N/A
CE Certified Yes Yes Yes Yes

Mixer Specifications (Metric)
Capacity 7.9m³ 9.4m³ 11.0m³ 13.2m³
Production Rate (m³/Hr.) 22.5 22.5 22.5 22.5
Cement (m³) 2.7 2.7 3.2 3.6
Water (Liters) 1893 1893 1893 1893
Ag Bin Capacity (m³) 7.9 9.4 11.0 13.2
Empty Unit Weight (kg) Contact ZI Contact ZI Contact ZI Contact ZI
Hydraulic Pump (Sections) 4 4 4 4
Patented Chain Delivery System Yes Yes Yes Yes
Auger Length (mm) 2743 2743 2743 2743
Auger Diameter (mm) 228.6 228.6 228.6 228.6
Meets Standards:
ASTM C685 Yes Yes Yes Yes
AASHTO M241 Yes Yes Yes Yes
Certified VMMB Plate N/A N/A N/A N/A
CE Certified Yes Yes Yes Yes
Chassis Specifications (English)
Capacity 10 Yard
12 Yard 14 Yard 17 Yard
Front Axle (Lbs.) 20,000
20,000
20,000
20,000
Rear Axle (Lbs.) 46,000
46,000 46,000
46,000
Cab to Axle (Inches)
155 155 155 155
Frame Width (Inches)
33.75 33.75 33.75 33.75
Number of Axles * * * *

Chassis Specifications (Metric)
Capacity 7.9M³ 9.4M³ 11.0M³ 13.2M³
Front Axle (Kg.) 9,072
9,072
9,072 9,072
Rear Axle (Kg.) 20,870*
20,870* 20,870* 20,870*
Cab to Axle (mm)
3937 3937 3937 3937
Frame Width (mm)
858 858 858 858


*Varies with state laws

Zimmerman Industries can supply you with a customized weight distribution package per your chassis and mixer specifications. Actual yardage carried with be determined by your analysis of regional weight regulations as well as weight rating of the chassis.

Please call our main office at 888-577-6499 (US only) or 717.733.6166 and speak to one of our sales people or complete the form below. We will work with you from the beginning of the inquiry to the final delivery of your machine.

Fields marked with a * are required.

Please prove you aren't a robot.

ZI Newsletter

Fields marked with a * are required.

Please prove you aren't a robot.

Follow Us!

Follow Us on Facebook   Follow Us on LinkedIn   Follow Us on YouTube