This option allows the production of up to 60 cubic yards per hour of a typical 5 bag mix as per VMMB Standards. Included in this option is our 9’ x 12” diameter mix auger, Material Feed Flow Control Valve, and a 12 volt Digital Tachometer for accurate control of the desired production rate.
Allows the use of liquid admixtures such as Air Entraining Agents, Water Reducers, Super Plasticizers, Accelerators, and Set Retarders. A holding tank is loaded with the liquid, and charged with air pressure from the Mixer Unit. Each tank has an inline Filter, and an electrically triggered valve. This is integrated with the Material Feed Valve to allow the flow of material to stop and start with the other mix ingredients. Flow Meters are sized to meet the delivery requirements of the product being used, with ranges from 1 ounce to 3.5 gallons per minute. Each Flow Meter is certified to meet the tolerance requirements of ASTM, +/- 3%. There are no pumps to flush or maintain, and the air pressure can be used to evacuate the lines for easy draining and cleaning of the system.
Low Flow Admixture System- For use with admixtures requiring lower dosages, a 20 Gallon Galvanized Tank is used (with a Stainless Steel Tank Optional) and a Flow Meter sized to meet the desired delivery rate.
High Flow Admixture System- For use with admixtures requiring higher dosages, a 42 Gallon Galvanized Tank is used (with a Stainless Steel Tank Optional) and a Flow Meter sized to meet the desired delivery rate.
This Chute System is standard equipment on all 400N1 series units. It is attached to the auger, and takes up no space on the decks of the unit. When in use, the discharge angle is adjustable, and the chutes can extend from 4 to 8 feet in six inch increments, allowing for a wide area of coverage. Since it is attached to the auger, it is moved by the Operator and requires no additional personnel.
This Chute System allows the Operator to change the angle of delivery as well as the length of the chute from 5 to 11 feet in any increment required. It is especially useful in flat work applications, as a large area can be placed without moving the mixer, and without the need of additional personnel. As with the Manual Telescopic Chutes, it is attached to the Auger and takes up no space when not in use.
This Chute System allows concrete to be placed in areas not reachable by fixed chutes. As with the other ZI Chute Systems, it is attached to the Auger and takes up no additional space on the unit when not in use, and requires no additional personnel. A ring is used at the top of the chute, and allows rotation in a 200 degree arc. This enables the concrete to be placed alongside the mixer, and is especially useful in curbing or trenching applications. The Chute angle is adjustable, and it is in a 2 piece configuration that can extend to either 5 feet or 10 feet from the end of the Auger.
This Chute is designed to aid in the placing of material into a concrete pump, wheelbarrow, or buggy. The lightweight 18 inch long chute quickly attaches to the discharge end of the mix auger, and minimizes any spills as well as simplifying wash out.
Provides light for nighttime operation. Lights illuminate the operator's control panel area, the aggregate bin material discharge area, and the work area.
VR Ticket Printer- Resettable mechanical counter with a non-resettable totalizer. The totalizer is useful for scheduling periodic maintenance. This ticket printer provides an immediate record of the concrete delivered.
- Resettable mechanical counter with a non-resettable totalizer. The totalizer is useful for scheduling periodic maintenance.
With our Digital Metering System, there is no longer a need to convert a count number, with many variations for mix designs, into cubic yards. Our units are able to show the operator, as well as the customer, an actual reading of cubic yards produced at any given moment. The LCD panel at the operator's station shows the cubic yards produced on a continual basis.
Our in cab Interface Panel stores all of the necessary information that the operator needs, along with the current yardage being produced. Gate settings for aggregates, flow meter readings for admixtures (as many as 6), and specified strength for up to 99 mix designs can be stored. If so desired, the panel can also store the quantities per yard of each component of all 99 mix designs and can be printed on each ticket.
The in cab printer can be loaded with the name, address and phone number of the producer, as well as the actual yardage produced. The mix design can also be printed for D.O.T. requirements. The printed receipt is available in 1 or 2 part format, so that the customer can be given a copy. The system also produces a cumulative record of production for inventory control or maintenance purposes. The information is stored on a removable memory card and may be downloaded directly to a computer via a USB cable.
An acrylic-reinforced aliphatic aromatic polyurethane coating applied to the inside of the aggregate bins to prevent bin abrasion, bin corrosion, and permit smooth flow of aggregates.
In cab switch provides easy operation to cover & uncover the aggregate bin. Most states require bin to be covered when loaded.
The use of fiber reinforced concrete within the construction industry is growing at a rapid rate. In fact, because of it's structural benefits, many architects and engineers are specifying fiber reinforced concrete in their projects. Zimmerman Industries has a patented fiber feeder that will automatically introduce the fiber into the mix auger.
The feeder is powered by a variable speed hydraulic motor, so the amount of fiber can be adjusted to meet various specifications. The fibers are stretched and fluffed through the use of rotating fingers and a high volume air flow system insures a consistent material flow to the mix auger. The Fiber Dispenser uses 1/2" to 1 1/4" (12.7mm to 31.75mm) polypropylene mono-filament.
Features and benefits include:
* Automatically feeds fiber
* Fluffs and stretches fibers
* Buy fiber in bulk, not bags
* Eliminate manual feeding
* Increased accuracy
* Patented system
Our Liquid Color System can be used with various manufacturers' liquid color products and is designed to allow changes of color in minutes. The variable speed peristaltic pump not only compensates to allow the changes of color needed (based on manufacturer's specifications), but also provides the availability to produce shades of each color.
Cleaning of the system can be done in minutes by simply flushing the system with clean water. The system is also designed so that it can be used to pump the liquid color from its' shipping container into the dispensing tanks.
Prevents possible damage of equipment by screening materials through a 2-1/2" x 2-1/2" (63.5mm x 63.5mm) opening. All units sold outside the United States will be equipped with bin screens.
Provides deck level fill port for the water tank. Prevents operator from having to climb on top of unit to fill water tank. Uses 1-1/2" (38.1mm) coupling.
This option can be added when high ambient temperatures are common. The radiator will help keep the hydraulic oil cool, extending the life of critical hydraulic components.
This option includes the cement bin, aggregate bin, and mixer main frame being manufactured of grade 304 stainless steel. It provides the owner confidence that corrosion will not deteriorate the mixer regardless of environmental conditions.
Non-transparent insulated blanket fastens to poly water tank insuring water temperature stays constant.
This option is used to service contractors, municipalities and utilities requiring the use of a high quality/low cost back fill material. The most common uses are for "Flowable Fill" and "controlled low strength material" mixes. Provided in this option is an infinitely controlled hydraulic variable speed motor, and two independently controlled stone bin vibrators.
This option provides the capability to produce concrete while the unit is moving. Used for sidewalks, filling ditches, and curb applications. There are several different models of this option available depending on customer and chassis specifications. The systems hydraulic power may come from a front mount pump, standard or automatic transmission PTO, Repto (rear engine PTO) or from a pony engine. Operator switches will be mounted in the cab for driver operation or may be tether/radio remote controlled for operation outside the cab.
Provides storage and metering of pozzolanic materials (ie. flyash, slag, etc.) to be introduced into the concrete mix. It includes hydraulic variable speed with a tachometer so that the pozzolan may be added quickly at any addition rate desired. It may be run independently from other materials and is available in various sizes to compliment cement production capabilities.
This option provides the ability to hydraulically control the cement feed with an infinite number of possibilities. This is most commonly used for companies with mix designs which require atypical cement/pozzolan addition rates.